My family has two computers, connected to the same router, a desktop computer is connected to the route through the connection, and a laptop computer is connected through a wireless network card on the route, two computers are now trying to set a LAN, but no matter how set in the computer can not see another. A friend told me different wired and wireless protocols, not even as a local area network. But I through practice, and finally even the good
method: two computers administrator account name are set to the same group.
XP computer interconnection of local area network interconnection
XP and XP articles
1.
hardware is connected with our machines before the computer is first to confirm that the two computer on the network are connected, and that hardware is connected. You can start - run using ping command to test. Both computers will be better to manually set their IP (eg 172.192.0.1 subnet mask 172.192.0.2 subnet mask 255.255.255.0 and the other is the same) using the command ping 172.192.1.2 (the IP is 172.192.0.1 computer use) to use ping 172.192.0.1 (IP is 172.192.0.2 use) to see whether two computers connected. If the connectivity of the can, and if not then the problem to check the hardware, such as the card is not good there is no network cable is not plugged in good general also the three situation.
specific setup steps on the IP:
My Computer - Control Panel - Network Connections - Local Area Connection Right Properties - General - to find TCP / IP protocol - Point the following attributes - General - Select Use the following IP address, Then fill in IP and subnet mask on it.
2. do not see each other in Network Neighborhood
please confirm your correct both the working group should be in the same working group which the specific operation is as follows:
shock Name To modify the words on the point of
3. appear the words account with machine
⑴ When you point your computer when machine network neighbors, possible reasons:
① XP itself comes with a network firewall is not turned off, turn off. Set as follows:
My Computer - Control Panel - Network Connections - Local Area Connection Right Properties - Advanced you can see, and to remove the hook, do not ignore the prompt.
⑵ neighbors in the network when you view the workgroup computers inside to see the other side, but when you click on the words above reasons:
① congratulate you because the computer in the other person is not on the
② turn off the firewall (its own, and later installed are likely to)
③ other party does not open the guest account
④ in My Computer - Control Panel - Administrative Tools - Security Settings - Local Security Policy - User Rights Assignment in the ; = dword: 00000001; against null if people change the two anonymous users can not connect to your IPC shared
this can be deleted.
4. even the machine is not necessarily to open the guest account
the answer is no, even the machines do not have to open the guest account. As long as you like, you can even have an administrator account login, just change the relevant settings on it. Set as follows:
My Computer - Control Panel - Administrative Tools - Security Settings - Local Security Policy - Security Options be. Then click on the other side even when the machine, the user own the column is filled, you can use any of the other computer users who have opened the landing. But the point to note is that there is a security option that is is empty but can not login. Then you can turn off the item or let the other party to the need to set a password for the account login.
5. on some of the problems
guest account to use the guest account for a landing, you need to open the guest account.
of two ways to open it. Method One. My Computer - Control Panel - Administrative Tools - Computer Management - Local Users and Groups - users find the guest right-click Properties, the account is disabled before removing the hook. Method II. My Computer - Control Panel - open guest user account directly, but should be noted that the two methods with the same effect as on the machine. But there are some differences between the machine, and later will be mentioned.
some understanding about the guest
we need to involve three things, first in front of that back to the direct use of following shorthand. a. located in the Computer Management - Local Users and Groups - Users of the guest to open. b. in the User Accounts control panel in the opening mechanism of the guest account. c. is located in My Computer - Control Panel - Administrative Tools - Security Settings - Local Security Policy - User Rights Assignment in the See the following figure:
*******************
* a Computer Management - Local Users and Groups * * the user of the guest's Open *
*******************
* * c
***************** ********************
b * control panel user account * * Local Security Policy User Rights Assignment *
* the guest account opening mechanism * * The refusal of local landing from the network *
****************** ******************* *
Note: Open on the guest account has two levels. The first level (highest level) is a right to control it is the highest; the second level is the b and c. For now, the next they are, a computer in the end it is to manage or not to open the guest account, either your own or a local network with the guest account with a guest account, log landing, if a said I banned, it will not work. Suppose a is open, then you say I want to use a computer in their guest landing, it would need to b opened, so you can use the guest account on the machine landed. And then you ask others through the network with the guest account to login to your computer, then you take a look inside the c, a guest can not log it, and can be deleted.
three on the guest's another problem
d. in My Computer - Control Panel - Administrative Tools - Security Settings - Local Security Policy - User Rights Assignment in the I found the d and b is interconnected. For example, you If you open the guest account again, that But if you banned in the computer management of guest, that the In fact, people should be careful that there are In addition, when the default in the guest computer management is prohibited, My system is this.
added:
in the actual use of the network, install Windows XP-based computer sometimes can not Windows 98, Windows 2000 issues of computer access each other, even if the Guest account is open, install the NetBEUI protocol , set the shared folder, the problem is not resolved. Today, e said that the Dr. is a common network problems.
Windows desktop, right-click Then click on the Select the Finally click Restart the computer, LAN computer can exchange visits of.
After such settings, even if the computer LAN set up different working groups, but in , the right of the window all the work will appear in the name of the group, enabling the exchange of visits of different working groups.
After setting I found the above still can not connect to the last set: a computer with wireless Internet access to Network Neighborhood, create a Network Neighborhood, My Network Places in the path Administrator Name is the shared folder name, the next step to the end just fine. you try.
No comments:
Post a Comment